Home decoration leaves no regrets and walks out of

2022-07-22
  • Detail

In home decoration, circuit transformation is a particularly important link, which is directly related to the safety of electricity in future life. When many families are decorating, the circuit transformation of the kitchen is often not well designed, resulting in inconvenience in the use process. Some sockets do not exist, but some sockets are wasted, which inadvertently caused the regret of decoration. Next, Xiaobian will introduce the construction mistakes of circuit transformation to you today. Let's understand them together

in home decoration, circuit transformation is a particularly important link, which is directly related to the safety of electricity in future life. When many families are decorating, the circuit transformation of the kitchen is often not well designed, resulting in inconvenient use. Some sockets do not exist, but some sockets are wasted, which inadvertently leads to the regret of decoration. Next, Xiaobian will introduce the construction mistakes of circuit transformation to you today. Let's understand them together

first, do a good job in circuit laying planning and do not enter the misunderstanding of wire laying

nowadays, wire laying is generally hidden in the wall, floor, underground, ceiling, so once you enter the misunderstanding of wire laying by mistake, it will be difficult to change, and you should not leave trouble and regret. Therefore, we must do a good job in planning the money for wire laying to prevent the following misunderstandings

misunderstanding 1. There is only one circuit

not only the previous houses, but also many houses now have the same situation, that is, there is only one circuit at home. Once any line is short circuited, the electricity consumption of the whole room will be paralyzed

small editor's advice: when we are laying point display, according to the use area, we can choose two or three lighting circuits and three to four power sockets. The kitchen and bathroom take one route respectively, and the air conditioning circuit is two to three routes. One air conditioning circuit can have two air conditioners at most. In this way, when one circuit fails, the other circuits can still supply power normally, which will not bring too much impact on normal life

misunderstanding 2. Unclear color separation of wires

we often see “ There are no specific requirements for the color of wires, as long as the colors of live wire, neutral wire and ground wire are separated ” This kind of wire color is used at will, which will have potential safety hazards in the future use and maintenance process. For example, in order to facilitate the drawing and save materials, the blue line is used as the live line and zero line during the circuit transformation. In the future maintenance, it is difficult for the maintenance master to find the live line and zero line, which brings inconvenience to the maintenance and is easy to cause construction safety accidents

small editor's advice: the color of wires is clearly stipulated in the considerable specifications of China's electrical industry. Red is the color code of live wire, blue, green or black is the color code of zero wire, and yellow green color line is the color code of ground wire. In a house, the color code needs to be distinguished clearly, and unified color separation is used during installation. If there is no unified color separation for the installed lines, it is recommended to mark the left side of the line and clearly mark it on the circuit direction diagram for future inspection

misunderstanding 3. Bend the tube directly at the tube bend

bending the tube directly at the tube bend is OK, but it is not good. If you don't pay attention to the work when the line bends, it will cause a lot of inconvenience in the future. If the line bends the tube directly, it is easy to cause line damage and lead to leakage accidents

small editor's advice: Although the electric tube should not be bent directly, it is also forbidden to use elbows at the corners of the electric tube. At the bend of the wire protection pipe, the supporting bending tool or supporting elbow should be used, and there should be no wrinkles. Increase the bending at the bending position, buffer the bending pressure and reduce the wear

misunderstanding 4. Wires are directly buried without casing

some irresponsible construction parties bury wires directly into the wall during construction, and the wires are not covered with insulating tubes, and the wire joints are directly exposed, which is easy to cause potential safety hazards. In future life, the wires lack protection, and are easy to be bitten by rats or external damage, resulting in short circuit of wires

small editor's advice: the laying specification of wires is clear, the wires must be protected by insulating sleeves, and the joints cannot be exposed. Therefore, during the construction supervision, the owner must supervise whether the construction party carries out the construction as required. If the wire has been laid, it is recommended to demolish the wall again for rectification to ensure the safety of household electricity

second, small details also need to consider the misunderstanding of socket construction

don't underestimate small sockets. Well installed sockets make your life convenient. There are sockets where there should be sockets; If the installation is not good, there will be some worries in the future. Next, let's learn about the misunderstanding of socket construction

misunderstanding 1. The socket position is too low

when installing the socket, many families feel that it is too high, inconvenient to use, and hinders the appearance. Therefore, they will install the socket in a low hidden position. But experts said that it is easy to splash water into the socket when mopping the floor, resulting in leakage accidents

small editor's advice: according to the industry regulations, the distance between the surface mounted socket and the ground should not be less than 1.8 meters; The concealed socket shall not be less than 0.3m from the ground. The sockets of kitchen and bathroom should be more than 1.5 meters away from the ground, and the sockets of air conditioner should be at least 2 meters away

misunderstanding 2. Random installation of socket wires

such misunderstandings often occur when the circuit of old houses is renovated or repaired. Many people think that the copper wire of the socket can be replaced by aluminum wire. In the absence of copper wire, aluminum wire is used as the wiring of the socket. This is easy to cause a fire in the circuit, which is very detrimental to home safety

small knitting tips: due to the special physical and chemical properties of aluminum wire, it is very easy to oxidize, which makes the joint easy to ignite. If the copper wire is replaced by aluminum wire, the joint is easier to ignite. After investigation, the probability of fire in homes using aluminum wire is dozens of times higher than that using copper wire. Therefore, when repairing and renovating circuits, copper wires must be used to ensure household safety

misunderstanding 3. Sockets lack protective measures

in order to meet the needs of life, sockets will also be installed in kitchens and bathrooms. Some people think that if waterproof sockets are used, they are not allowed to add cover protection to sockets. In this way, the socket is easy to be invaded by oil and water vapor, causing a short circuit

tips: there is often water and oil smoke in the kitchen and bathroom. Therefore, it is best to install a splash proof box or plastic baffle on the socket panel, which can effectively prevent short circuits caused by the invasion of oil and water vapor. For families with children, in order to prevent children from touching or stabbing the socket eyelet with their fingers or metal objects, they should choose a safety socket with a safety shield

misunderstanding 4. Multiple electrical appliances share the same plug

now multifunctional plugs are available on the market to facilitate people's daily life. However, if too many electrical appliances use one plug at the same time, it is easy to overload the socket and cause a short circuit, which may burn out the electrical appliances at first, or cause a fire at last

tips for small editors: it is best to use independent sockets for high-power electrical appliances such as air conditioners, washing machines, range hoods, etc. Generally speaking, it is best to install four sets of sockets in the bedroom, one for every 2.5 square meters in the living room and one for every 1.2 square meters in the kitchen. If multi pole plugs are used, the electrical appliances on the same plug should be serialized to avoid using them at the same time, so as to reduce the burden of sockets

杭州皮肤病医院

天津试管婴儿医院

上海精神医院

Copyright © 2011 JIN SHI